How Do I Change The Filter On My Shark Navigator Lift Away Deluxe Vacuum

I'1000 pretty certain you know by now just how much I beloved my Shark vacuum cleaner. And given my readers' messages and comments, I know that many of you have Sharkys, too. Information technology'due south super important that you know how to clean a Shark vacuum to brand sure it keeps performing at elevation efficiency both at present and for many years to come.

I dear your messages. They make me smile because I sympathise the range of emotion that comes with using a Shark vacuum for the start fourth dimension—from amazement to flat out embarrassment.

Where on earth did all of this dirt and droppings come from? I can't believe what's been lurking in my carpet!

With all of the miles I've put on my numerous Shark vacs over the years, I've never had one fail. And while the manufacturer boasts that Sharks never lose suction, that is predicated on mutual sense and regularly cleaning Sharky'due south canister, filters, rotating brush, and handle hose.

Yous'll know it'southward time when …

Step 1: Disassemble

Step 2: Clear obstructions

Step iii: Scrub canister clean

Step iv: Shark vacuum filter cleaning

Step 5: Untangle roller brush

Pace 6: De-gunk handle hose

Stride 7: Reassemble

FAQs

Signs a Shark vacuum needs cleaning

Loss of suction: It happens. A big fatty hairy fuzzball or a venerable filter that'southward stopped filtering tin clog a vacuum and cutting off suction. Whatever the crusade, a loss of suction is the first sign that someone needs a good cleaning.

Visible dirt left behind: When working at elevation performance, a Shark vacuum will never leave behind a trail of crumbs and droppings. If information technology does, that's a clear indication information technology needs to be cleaned.

Weird sound: Y'all'll know it's bathtime for sure if your Shark sounds similar it is gasping for air. That'southward considering information technology is. And that can exist very hard on the vacuum's motor.

Unpleasant smell: A Shark vacuum should never give off a stinky, dingy smell. If it does, consider that a clear sign this vacuum is overdue for a good cleaning.

How to clean a Shark vacuum

In the more than 12 years I've been using Shark vacuums, the company has come out with a crazy number of models. Nevertheless, my experience is that all Shark vacuums have the aforementioned basic parts and operate in much the same way.

What follows are general instructions. Your detail Shark model may vary. If you get stuck, ask in the comment area below, or refer to your possessor's manual.

What yous'll need

✅ warm water

✅ dishwashing liquid

✅ cleaning cloth

✅ wood skewer, or similar

✅ flashlight

✅ soft brush like a bottle brush

✅ pair of scissors

Step 1: Disassemble

Make certain the vacuum is asunder from ability, then take it apart. Don't go crazy hither. We're not talking almost removing screws or detaching wires. Remove the dust canister and the foam/felt filters, the HEPA filter and its encompass, and the handle hose.

Shark Vac Cleaning Disassemble

Take annotation of the placement of the filters and then that y'all can replace them in the aforementioned proper order. It'due south not difficult. Just pay attention.

Step 2: Check for and articulate obstructions

Check every opening. You're probable to meet fuzz, hairballs, and clinging dust. You may find other things like a Lego brick or maybe even a sock!

Shark Vac Step 3 obstructions

Remove all obstructions using your hand or a clammy microfiber cloth. Can't accomplish it? A wooden skewer works well to fish out or release any weird aggregating.

Pro Tip

Make sure you are working in a well-lit area and using a flashlight to help search for blockages.

Pace iii: Empty and clean the dirt canister

Open both ends of the dirt canister over a trash can and dump out whatever is in at that place. Now take the canister to a sink of warm soapy water.

Step 3 cleaning Shark vacuum

Open both ends of the dust canister and put information technology right into that warm bathroom. Using a long-handled brush or a rag, get inside that canister and scrub it make clean. Once rinsed, dry out it thoroughly with a practiced microfiber cloth.

More: And so Disgusting I'grand Embarrassed to Tell

Step four: Shark vacuum filter cleaning

Shark vacuums have an splendid filter arrangement consisting of one or two (depending on the model) thick foam filters plus one made of felt; and a HEPA filter.

collage of shark vacuum filters

Foam/Felt Filters

Rinse the foam and felt filters in cool, articulate water (manufacturer recommends no soap), being particularly conscientious not to impairment them.

Information technology takes a good corporeality of squeezy and scrubbing of the foam filter to get it clean. Once cleaned and rinsed well, the filter(due south) may or may not return to their new white appearance. But don't worry. As long equally they are non torn, broken, or otherwise disintegrated, they'll be just fine, even if they remain stained.

NOTE: The manufacturer does not recommend washing the felt filter. I'k not too addicted of dingy felt, so I advisedly hand launder and have done so many times with no problem. Do this at your own risk.

HEPA Filter

Most Shark vacuum models have an additional filter—a HEPA filter. This is located on the lower front of the motorcar behind the filter grill (door). Firmly pull the door off to reveal the HEPA filter and pull out the filter. Rinse the filter well in articulate water and allow it to dry fully.

Do not return the filter(southward) to the vacuum at this point. They must exist completely dry get-go or ready for mildew and mold—the last thing yous always want growing within a vacuum. Set the still wet filter(southward) on the counter so they can air dry. This may require an overnight stay.

MORE: The Best Way to Vacuum Carpet is to Memorize this Routine

Stride 5: Make clean the rotating brush head

Next, lay the vacuum on the floor then you tin see the rotating brush. Y'all may want to identify a handbag or towel underneath to grab the droppings and dirt you're nearly to release.

More than likely, you will see strings, hair, and other cloth wrapped around the brush. This is normal. I use scissors to cut through whatever has wound itself around the brush. That makes it easy to clean upwards the brush. You lot may take to pull and tug a bit, only it will come off. You want to return the rotating brush to its prissy and make clean condition.

Step half-dozen: Clean the handle hose

Again, since I am not privy to every single Shark model, please bank check your owner's manual before cleaning the vacuum handle hose. You want to make sure the hose on your model does not have whatever electric components. None of my Shark vacuums always have, only let'due south brand sure.

hose handle cleaning collage

The handle hose on a Shark disconnects easily. When you practice this and take a look inside, you lot'll run into that it is laden with sticky dust and grime. Removing all of that will assistance your Sharky to proceed to perform smoothly.

Take the hose to your sink or tub of soapy water and drop it in and so it tin can fill up with water. Using a castor or rag, reach into the ends to clean information technology. Warning! Don't get anything get stuck, especially in that bendy function.

Permit the hose to sit and soak for a while, to loosen the grime in the areas you cannot reach easily. Finish past running clean water from a faucet through the hose until it comes out clean and clear from the other cease. Notice a place to hang the hose vertically so it can drip dry.

MORE: How to Clean Carpet Even if It's Onetime, Stained, and Disgusting

Step 7: Reassemble the vacuum

In one case the filters and handle hose are completely dry, reassemble your Shark vacuum.

reassemble collage

Replace the felt filter kickoff. Next, replace the clean foam filter on acme of the felt filter. Replace the HEPA filter and and then the "grill" cover. Reattach the handle hose. Close both ends of the dirt canister and lock it into identify.

Enjoy your prissy clean, fresh Shark Vac!

FAQs

Why does my vacuum scent?

More than probable, you are not emptying the dirt canister oftentimes enough. But call back about what goes inside that clay canister and also gets trapped in the filters. It'southward dirt and debris from the outdoors, bits of food, and other organic matter. Allowing that debris to remain in the dirt canister creates a breeding basis for bacteria and mold and the potential for a stinky situation.

How often should I make clean a Shark vacuum and filters?

Each utilize: Empty the dirt container after every use.
Monthly: Shark vacuum owner manuals mostly instruct that the foam/felt filters should be cleaned monthly.
Quarterly: Every three months, take the vacuum apart (run across above), requite the dust canister, castor roll, and hose a good cleaning.
Annually: Clean the HEPA filter once each twelvemonth.

When should I supervene upon Shark vacuum filters?

Your owner manual volition well-nigh probable advise both the cream/felt and HEPA filters to exist replaced once you find the machine is losing suction, even subsequently cleaning the filters as mentioned to a higher place. That's a strong sign that the filters are no longer constructive.

To be on the safe side and since they are not expensive, my do is to replace the cream/felt filters annually and the HEPA filter as needed.

Where can I get filters and replacement parts for my Shark products?

SharkClean.com carries merely about every possible replacement office or accompaniment you can imagine and for lots of Shark models, fifty-fifty those that are no longer in product. As for filters, I compare prices at SharkClean with Amazon, where the filters for my Sharks are usually a bit less expensive. You lot can besides find owner manuals for hundreds of models and infrequent support at SharkClean.

At that place are so many models of Shark vacuums. Do you have a recommendation?

You're right, there are many models to choose from! I am partial to the models with the Lift-Away feature, making it piece of cake and efficient to vacuum a staircase. And I prefer the Navigator line of Shark vacuums because they maneuver and so well.

I purchased the vacuum in this photograph tutorial in a higher place in 2015. You wouldn't believe how many miles I take on it, and it withal looks and operates as if new.

My current recommendation is this Shark Navigator Pro Lift-Away. Information technology comes with several accessories including a pet power brush and crevice tool. It weighs in at just thirteen.7 lbs., which is just ane more than thing to honey.

Everyday Cheapskate participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a ways for us to earn from qualifying purchases, at no toll to you.

Original: 12-30-fifteen; Republished with updated photos iii -21-22

More from Everyday Cheapskate

Where to Find Basic Essentials When the Shelves are Empty

Peak Ten Signs a Website is Not Legit—Information technology's a Scam!

A group of people walking through a cloudy sky

6 Reasons We Need to Celebrate Before long—and Oft!

DIY Floor Cleaners for Forest, Laminate, Luxury Vinyl, Tile, Swiffer Refill

dog and cat in front of white background

Got a Pet Hair Problem? Here Are The All-time Tools to Keep it Under Control

4 Kitchen Money-Savers That Pay for Themselves in No Fourth dimension at All

How to Make Cut Flowers Stay Fresh and Beautiful Twice as Long

Now is a Good Fourth dimension to Join a CSA for Your Wellness and Wealth

Ask Me Anything: Credit Reports, Storing Potatoes, Deadbeat Relatives and More!

Please keep your comments positive, encouraging, helpful, brief,
and on-topic in keeping with EC Commenting Guidelines

How Do I Change The Filter On My Shark Navigator Lift Away Deluxe Vacuum,

Source: https://www.everydaycheapskate.com/how-to-clean-a-shark-vacuum-and-filters/

Posted by: stokesfrighters.blogspot.com

How Do I Change The Filter On My Shark Navigator Lift Away Deluxe Vacuum

Contents

Signs a Shark vacuum needs cleaning